|ISO Size||20FT ISO - 6058mm x 2438mm x 2591mm|
|Material Tank Body||Mild / Carbon Steel|
Approvals by Lloyd's Register, the Netherlands
Danteco supplies 25,000-litre ISO bulk bitumen tank containers. Our bitumen tank containers are separated for four purposes: tank containers for bitumen storage, short-sea, deep-sea shipping, and rail transportation. All Danteco tanks have the highest quality design and construction and conform strictly to the latest international approvals.
Please note that in certain exceptional cases, the containers operated by Danteco may have specifications that differ from the descriptions above.
Also, cargo in the container must conform to the dimensional regulations and laws stipulated by the host country; thus, payload capacity may be affected. For more information or assistance, please contact our customer service.
A heat-resistant metal tube inside the Danteco bitumen tank where the actual combustion occurs of the burner.
6058mm x 2438mm x 2591mm, 2.65 bar test pressure, insulated, flame tube type, direct fire, re-heating by a diesel burner or LPG gas burner
|Capacity Tank||25000 LTR||(6604 US GALLONS) 5500 GALLONS|
|Maximum Gross Weight||30480 KG||67196 LBS|
|Tare||5950 KG||13118 LBS|
|Working Pressure||1.75 bar||25 psi|
|Test Pressure||2.65 bar||39 psi|
|Relief Valve Set Pressure||2.2 bar / -0.21 bar/vac||32 psi / -3 vac/psi|
|Ambient Temp. Range||-40°C up to +200°C||-40°F up to +392°F|
|Maximum Cargo Temp||230°C||446°F|
|Shell Material||Mild Steel Q345D-GB/T1591-2008, 6,0 mm shell, 8,0 mm dish ends, the head is not less than 7,0 mm after forming.|
|Design Code / Approvals||ASME, Section VIII, Division 1 where applicable and IMDG T3, DOT UK, USDOT, UIC, IMO2, FRA, CSC, ADR, RID, CTC Transport Canada.|
|Manlid||500mm (20") diameter, 6 point fixing, 14mm x 12mm seal, located centre.|
|Calibration||volumetric chart, nominal capacity 25,000 liters available.|
|Airline / Vapour||40MM (1½") ball valve, outlet 1½" BSP, s/s screw cap.|
|Relief Valve||65MM (2½") high flow flanged, operating pressure 2,2 bar. Capacity: 8710m3/hr.|
|Top Inlet||Blanked weld-in flange drilled 6x M12 holes @ 168 pcd, provision for optional fitting of 80mm (3") stainless steel butterfly valve. DN80, ASA 150 bolted blank flange outlet, 80mm (3") removable full-length syphon tube.|
|Bottom Discharge||Guard 100MM 4" Ball valve - Outlet 3" BSP Flange with 3" Cam Lock Coupling and 3" Dust Cap.|
|Gaskets & Seals||Parts in contact with cargo, PTFE/Teflon.|
|Flame Tube Heating||Φ159x6.0mm, Φ219x6.0mm.|
|Insulation||50MM (2") inorganic Rockwool (CFC free); 1,0 mm aluminium cladding; Thermal conductivity: ≤ 0.044 w/(m2.k).|
|Document Holder / Earth||Fitted at the rear end, suitable for shipping documents, MSDS, etc. Earth is located at the rear.|
|Data Plate / Markings||Stainless steel data plate detailing specifications are fitted @ the rear end.|
|Frame||The container frame shall be mainly composed of two (2) end frames, two (2) barrel supports, two (2) top side rails, two (2) bottom side rails, four (4) tank supports, and eight (8) corner fittings.|
|Walkway||400MM-wide non-slip steel. One longitudinal walkway and three short transverse walkways at the front and rear and adjacent to the rear of the manhole’s spill-box. Aluminum walkways.|
|Handrail||(Optional) Intergraded at the top rail.|
|Temperature Gauge||Analog gauge fitted rear end: -20°C to +300°C. / -4°F to +572°F.|
Actual measurements and specifications may vary and are subject to confirmation.
Tank containers are supplied per the manufacturer's (Danteco Industries BV) general trading terms and conditions.
International statutory authorities approve the pneumatic-operated cement tank with the danteco aeration system ...Show More
For Propane, LPG, and Anhydrous Ammonia, Danteco offers a full range with various pressure ratings of new and us...Show More
Nitric Acid UN 2031 is a component to produce ammonium nitrate, a major component of fertilizers. It is als...Show More
© COPYRIGHT 2022 - DANTECO INDUSTRIES BV