SPECIALISTS IN TANK CONTAINERS
Bitumen Tank Thermal-Oil Bitumen Tank Thermal-Oil Bitumen Tank Thermal-Oil Bitumen Tank Thermal-Oil
Stock Upon request
ISO Size 20FT ISO - 6058mm x 2438mm x 2591mm
Material Tank Body Mild / Carbon Steel

Danteco supplies a 25,000-liter bitumen tank, 20FT ISO bulk, with a thermal-oil heating system for PMB bitumen grades. Our Intermodal bitumen tank is separated into four purposes: bitumen storage, short-sea shipping, deep-sea shipping, and rail transportation. All Danteco tank containers are of the highest quality in design and construction and strictly conform to the latest international approvals. 

Please note that in certain exceptional cases, the containers operated by Danteco may have specifications that differ from the descriptions above.

Also, cargo in the container must comply with the dimensional regulations and laws of the host country. Thus, payload capacity may be affected. For more information or assistance, please contact our customer service. 

  • T3 20FT ISO Full Frame Design
  • Design temp. -40°C up-to +200°C / -40°F up-to +392°F
  • Thermal Oil (Hot-Oil) Design heating system
  • 3" and/or 4" Bottom Discharge includes 3" Cam-Lock coupling (m) & dust cap
  • Heavy Insulated 50mm
  • Approvals by Lloyd's Register, the Netherlands

SPECIFICATION BITUMEN TANK THERMAL-OIL 20FT ISO: 25000-Litre UN Portable Tank T3 

6058mm x 2438mm x 2591mm ISO Size, 2.65 bar test pressure, insulated, thermal-oil type

Year manufactured: New Build

Dimensions:
  Metric Imperial
Capacity 25000 LTR 5500 US GALLONS
Maximum Gross Weight 30480 KG 67196 LBS
Tare 5300 KG 11684 LBS
Construction:
Working Pressure 1.75 bar 25 psi
Test Pressure 2.65 bar 39 psi
Relief Valve Set Pressure 2.2 bar / -0.21 bar/vac 32 psi / -3 vac/psi
 
Ambient Temp. Range -40°C up-to +200°C -40°F up-to +392°F
Maximum Cargo Temp 230°C 446°F
Shell Material Mild Steel Q345D-GB/T1591-2008, 6,0 mm shell, 8,0 mm dish ends, the head is not less than 7,0 mm after forming.
Design Code / Approvals ASME, Section VIII, Division 1 where applicable and IMDG T3, DOT UK, USDOT, UIC, IMO2, FRA, CSC, ADR, RID, CTC Transport Canada.
Standard Fittings:
Manlid 500mm (20" diameter, 6-point fixing, 14mm x 12mm seal, located center).
Calibration Volumetric chart, nominal capacity 25,000 liters available.
Airline / Vapor 40MM (1½") ball valve, outlet 1½" BSP, s/s screw cap.
Relief Valve 65MM (2½")high flow flanged, operating pressure 2,2 bar. Capacity: 8710m3/hr.
Top Inlet Blanked weld-in flange drilled 6 M12 holes @ 168 pcd, provision for optional fitting of 80mm (3") stainless steel butterfly valve. DN80, ASA 150 bolted blank flange outlet, 80mm (3"" removable full-length syphon tube.
Bottom Discharge Guard 100MM 4""ball valve - Outlet 3""BSP Flange with 3""Cam-Lock Coupling and 3""Dust Cap.
Gaskets & Seals Parts in contact with cargo, PTFE/Teflon.
Heating Method:
Thermal-Oil (Hot-Oil) Type 14 pcs 2""seamless steel pipes are fitted at the bottom of the tank barrel, with a volume of 180 litres.
M.A.W.P / Test of Heating Pipe 5 bar / 13,5 bar.
Heating Area Tubes 17 m2 / Heating Pipe design temp. 230°C.
Expansion Tank Located under the bitumen tank's topside rail, it is the solution to the valve-leakage problem caused by thermal expansion when shutting off the thermal oil heating system.
Insulation 50MM (2") inorganic Rockwool (CFC free); 1.0/1.2 mm aluminium sheet cladding; Thermal conductivity: ≤ 0.044 w/(m2.k).
Document Holder / Earth It is fitted at the rear end and is suitable for shipping documents, MSDS, etc. Earth is located at the rear.
Data Plate / Markings Stainless steel data plate detailing specifications fitted at the rear end.
Frame The container frame shall be mainly composed of two (2) end frames, two (2) barrel supports, two (2) top side rails, two (2) bottom side rails, four (4) tank supports, and eight (8) corner fittings.
Walkway 400MM-wide non-slip steel. One longitudinal walkway and three short transverse walkways at the front and rear, adjacent to the spill box of the maintenance hole. Aluminum walkways.
Handrail (Optional) Integrated at the top rail.
Temperature Gauge Analog gauge fitted at the rear end: -20°C to +300°C. / -4°F to +572°F.
Color RAL 9005 or custom

Actual measurements and specifications may vary and are subject to confirmation. 
Tank containers are supplied in accordance with the manufacturer's (Danteco Industries BV) general trading terms and conditions.

Related Products

20FT Offshore Cement Silo Container DNV 2.7-1 and DNV 2.7-3

20FT Offshore Cement Silo Container DNV 2.7-1 and DNV 2.7-3

Offshore-rated ISO Bulk Cement Silos from Danteco are used to transport and store powdered cement for marine ene...

Show More
ISO Powder Tank Container

ISO Powder Tank Container

International statutory authorities approve the pneumatically operated cement tank with the Danteco aeration sys...

Show More
Bitumen Tank HC Flame Tube

Bitumen Tank HC Flame Tube

Danteco supplies 25,000-liter 20FT HC (high-cube) ISO bulk bitumen tank containers with a pair (two) flame ...

Show More
Swap Tank Container

Swap Tank Container

A Swap Tank (Swap Body) has a larger tank than the frame; it is usually 23 or 25 feet (7.01 or 7.62 meters)...

Show More